 |
or |
|
We are currently offering Google checkout for US residents only. International residents, please use our secure shopping cart. |
Brand New in the Factory Sealed Packaging
This 3 blade, rotary coax cable stripper is an economical, high-performance coaxial stripper with a strong ergonomic design. This will perform two and three-level stripping of coaxial cables, stripping the outer jacket, braided shield and inner dielectric. The adjustable blade depth works well for different coaxial cable thicknesses. This coax cable stripper makes it easy to have the right preset stripper for the job. If you need to adjust the blades, simply use the included hex key that makes it easy to set the new cutting depth. The stripping diagram on the top of the stripper makes it quick to select the proper tool for the coaxial cable you're using. Self-regulating tension means that you don't have to hold the jaws down on the cable. Just insert the cable and spin the tool in the direction of the arrow on the side.
- Easily adjustable blade depth for different cable thicknesses
- Self-regulating stripping method
- Pre-set strip lengths to work for most common connectors
- Economical price with high-quality performance
- Clear cable illustration on top of tool for cable placement and embossed arrow for spin direction
Who should own this stripper?
This stripper is great for anyone that needs to make consistently precise cuts on RG-58, RG-59,RG-6, RG-6 Quad Shield or RG-400 coaxial cable. This would include all satellite & CATV installers; electricians, maintenance personal or the "do it yourselfer". This stripper is made for everyone. If you are going to install any coaxial cable you need this stripper.
How will you benefit from owning this stripper?
By purchasing this stripper you will be able to make consistently precise cuts on RG-58, RG-59, RG-6, RG-6 Quad Shield or RG-400 coaxial cable. The secret to a good F connector installation is a properly cut and prepared coaxial cable.
You know, I have watched a lot of electricians use wire strippers, razor knives, side cutters, diagonal cutters or anything else at their disposal to strip coaxial cable. I have noticed that it usually takes them twice as long to strip the cable and they usually "hack" the end so it doesn't work very well.
Using this stripper you will strip the end quickly and perfectly every time. One of the best things about this stripper is it will work with RG-58, RG-59, RG-6, RG-6 Quad Shield or RG-400 cable without changing any cartridges.
Will this stripper work for the snap-n-seal type F connectors?
Yes it will. This 3 blade rotary coax cable stripper will strip your coaxial cable in 3 separate levels; the outer jacket, the inner shield and the dielectric. Please see image below.
Instructions
Blades Depth
Once adjusted to work with your coaxial cable size, the blades are preset and usually no adjustment is needed. But if you find the stripper doesn't strip your cable well or you are changing cable sizes, then you may use the included hex wrench to adjust the blades depth. Simply insert the hex wrench into the blade depth adjuster on the bottom of the stripper, the rotate the hex wrench clockwise (to cut smaller cable) or counterclockwise (to cut larger cable). Repeat the steps above to adjust the other blade(s).
Stripping the Cable
1. Press the knurled portion on the upper jaw to open the stripper's jaws.
2. Insert the cable you want to strip through the V-block until the cable reaches the V-shaped cable guide. Then release the upper jaw to close the jaws.
3. Insert your index finger into the stripper's finger ring, turn the stripper clockwise 3 — 5 times. The cable's insulation is cut while you turn the stripper.
4. Open the jaws and remove the cable. Pull away the outer jacket and dielectric to expose the inner conductor.
Buy It Now $10.50
|
or |
|
We are currently offering Google checkout for US residents only.
International residents, please use our secure shopping cart.
top of page
| 
Shipping & Handling